Forums
Yankee-RC.com :: Forums :: Technique :: Piste 1/4 |
|
<< Sujet précédent | Sujet suivant >> |
Yankee Williams Renault 1:4 |
Aller à la page 1 2 3 4 5 6 7 8 | |
Modérateurs:Gadman, WINGSAT, Brys, Jocelyne
|
Auteur | Message | ||
piou74 |
| ||
Membre enregistré #696 Inscrit(e) le: sam. 29 janv. 2011, 19:34Messages: 296 | Hello Bernd30, Your project is very nice and very clean too ! See you soon | ||
Retour en haut | | ||
bernd30 |
| ||
Membre enregistré #812 Inscrit(e) le: dim. 11 déc. 2011, 00:02Messages: 52 | thanks for your attention i hope i can finish the car at summer 2012 ... we will see ........ good luck and happy new year to all yankee fans of the world | ||
Retour en haut | | ||
Whozenext |
| ||
Membre enregistré #224 Inscrit(e) le: jeu. 17 avril 2008, 00:00Messages: 646 | Hello Bernd, Very nice , did you put some alloy inserts where are the holes to make it stronger, they did that on the tecma version II for carbon chassis plate, cause the screws with the physical contrainsts sometimes break the fibers. Maybe somebody who have the experience could give some more acurate advices on it, my two cents. Which sheme will you put for the body? Cheers. Whoz. | ||
Retour en haut | | ||
zatarra |
| ||
Membre enregistré #820 Inscrit(e) le: mer. 28 déc. 2011, 18:11Messages: 8 | hi bern, you remenber? look this pictures. how are you? | ||
Retour en haut | | ||
bernd30 |
| ||
Membre enregistré #812 Inscrit(e) le: dim. 11 déc. 2011, 00:02Messages: 52 | hey zatarre .... you are here thats good:-) how are you ? i hope you are nit shocked about my projekt ... @whozenext i want make it with a special glue for carbon on the underside of the chassisplate, so i hope the fibers dont break ! greets | ||
Retour en haut | | ||
bernd30 |
| ||
Membre enregistré #812 Inscrit(e) le: dim. 11 déc. 2011, 00:02Messages: 52 | hey friends FORUM YANKEE is not a Web site of classified adsgreets Sorry WINGSAT [ Édité ven. 06 janv. 2012, 09:37 ] | ||
Retour en haut | | ||
bernd30 |
| ||
Membre enregistré #812 Inscrit(e) le: dim. 11 déc. 2011, 00:02Messages: 52 | news news news my carbon front plate is here in 4mm , i had install all parts without the engine , exhaust and frontwing and the wight is 7,2 kilogramms perfect ... look at next i will make a full carbon rear wing and frontwing greets | ||
Retour en haut | | ||
FT |
| ||
Membre enregistré #301 Inscrit(e) le: mar. 12 août 2008, 22:14Messages: 1210 | I bernd Magnificent. Is not too soft in the middle with only 4 mm carbon? François | ||
Retour en haut | | ||
bernd30 |
| ||
Membre enregistré #812 Inscrit(e) le: dim. 11 déc. 2011, 00:02Messages: 52 | hy it cames a 2,5mm carbon chassisplate in 60cmx36cm over the 5mm plate in the middle - at finish is in the middle 7,5mm carbon,i think/jope that is hard enough the frontplate is 4mm | ||
Retour en haut | | ||
bernd30 |
| ||
Membre enregistré #812 Inscrit(e) le: dim. 11 déc. 2011, 00:02Messages: 52 | Today I have the body adapted, here some new good pics for yankee formula 1 fans here best regards | ||
Retour en haut | | ||
Aller à la page 1 2 3 4 5 6 7 8 | |
Powered by e107 Forum System